The OBDII trouble code of P0335 is well-known as a “hard” code, meaning severely detrimental come the procedure of her Accord engine. An ext specifically the DTC P0335 represents a absence of signal from the crankshaft place sensor. The crankshaft position sensor in your Honda Accord informs your ECU that the crankshaft speed and also current location.

You are watching: Honda accord crankshaft position sensor location

Without this data, the engine will certainly either not run or run very poorly. Typical symptoms are challenge starting or the engine may shut turn off randomly, developing a very dangerous case for not just the driver but the passengers together well.

Possible reasons of OBDII examine engine irradiate P0335Bad or weak batteryBad StarterBad crankshaft place sensorDamaged sensor harness

Today I’ll be reflecting you how to service and replace her crankshaft position sensor in a 2000 Honda Accord through a F23A1 VTEC SOHC engine.

The part number for this part is 37840-P0A-A01 because that the crankshaft place sensor in your Honda Accord. It can likewise be found under the component number of 37840-PAA-A01.


*

This How To adjust a Honda Accord Crankshaft position Sensor DIY guide assumes you have already removed your driver next engine mount and supported your engine with a jack. Please inspect our just how To change a Honda Accord time Belt guide for more details.

Before you begin our DIY overview on exactly how To change a Honda Accord Crankshaft position Sensor, you need to disconnect the an adverse terminal on your battery. As proclaimed previously, this guide assumes you have the right to raise and also lower your F23 already, i m sorry is mandatory when changing your time belt.

*

Unplug your four pin connector that runs to your crankshaft position sensor in her Honda Accord. Here’s what your pigtail looks like an installed to her F23A1. It’s secured by a 10mm bolt the runs through the earlier of your VTEC SOHC engine.

*

This exploit to your crankshaft place sensor runs with your reduced timing plate, which need to be eliminated to change a Honda Accord Crankshaft position Sensor. In bespeak to carry out this, friend must lower your engine if still linked to your chassis, and also remove the crankshaft wheel or harmonic balancer.

This might be difficult if you room working ~ above the ground v hand tools and also don’t have a waiting compressor with the best air tools. Usage a Honda crankshaft wrench, Moroso part number 61805 to correctly loosen your crankshaft bolt there is no air tools.

*

With the bolt removed, girlfriend should be able to wiggle off her crankshaft sheave and collection it safely come the side. Make sure eliminate your woodruff key and save that together safe as your pulley.

*

Now you have the right to remove every the 10mm bolts that hold your reduced timing sheathe in place. Eliminate these one-of-a-kind bolts and also then do your method to the valve cover, friend will require to earlier off the valve cover bolts the run through to the cylinder head.

Loosen all the valve cover bolts, yet do no remove and also gently loosen your valve cover. Elevator the valve cover to permit enough space for your upper SOHC VTEC timing cover to come off your engine. There space 2 10mm bolts the run with the top cover come the cylinder head, eliminate these to loosen your upper timing cover.

*

Now slide turn off your reduced timing cover and also pull down to relax from her side motor mount. You must now view your time belt assembly as well as your F23A1 balance shafts and also belts. The crankshaft place sensor in your Honda Accord is situated behind the crank create plate.

*

You can take one of two paths to removing your crankshaft place sensor and replacing it. You have the right to loosen her timing belt tensioner bolt, the longated bolt located in the middle of your tensioner arm. This should permit enough slack regarding gently back off your lower crank wheel plate and undo the 10mm bolt that holds the crankshaft position sensor in place.

*

If this is no an alternative for you, inspect out our exactly how To change a Honda Accord time Belt guide on exactly how to effectively time and remove her F23A1 belts to business your crankshaft position sensor.

There are number of timing marks for her balance shaft that us recommend girlfriend line approximately TDC before removing your balance pillar belts.

See more: This Is An Element With Full Valence Shell, Very Unreactive.

*

Before removing your balance obelisk belts to reach your crankshaft position sensor, you will require to twin check time marks to ensure her F23a1 is at TDC. Again for much more details inspect our how To DIY overview on an altering the Honda Accord time belt.

*

Once you have actually replaced your Honda Accord crankshaft position sensor, you have the right to use a scan device to effectively clear her OBDII examine engine password of P0335. Hope we’ve aided you learn exactly how To readjust a Honda Accord Crankshaft place Sensor, if friend have any questions please leave united state a comment below!